Diodes symbol and layout

Diodes

As with transistors, diodes are fabricated from semi-conducting material. So, the first letter in their identification is A for germanium diode or B for silicon diode. They can be encased in glass, metal or a plastic housing. They have two leads: cathode (k) and an anode (A). The most important property of all diodes is their resistance is very low in one direction and very large in the opposite direction. 

When a diode is measured with a multimeter and it reads a low value of ohms, this is not really the resistance of the diode. It represents the voltage drop across the junction of the diode. This means a multimeter can only be used to detect if the junction is not damaged. If the reading is low in one direction and very high in the other direction, the diode is operational. 

When a diode is placed in a circuit and the voltage on the anode is higher than the cathode, it acts like a low value resistor and current will flow. 

If it is connected in the opposite direction it acts like a large value resistor and current does not flow. 

In the first case the diode is said to be "forward biased" and in the second case it is "reverse biased." 

The diodes above are all single diodes, however 4 diodes are available in a single package. This is called a BRIDGE or BRIDGE RECTIFIER.

You must be able to identify each of the 4 leads on a bridge so that it can be inserted into a circuit around the correct way. The surface-mount device above is identified by a cut @ 45° along one side. The leaded bridge has one leg longer than the others and the top is marked with AC marks and "+." The high-current bridge has a corner cut off and the other surface-mount device has a cut or notch at one end.

There are a number of specially-designed diodes: for high current, high-speed, low voltage-drop, light-detection, and varying capacitance as the voltage is altered. Most diodes are made from silicon as it will withstand high temperature, however germanium is used if a low voltage-drop is required. There is also a light emitting diode called a LED, but this is a completely different type of diode.

LEDs (Light Emitting Diodes) are constructed from a crystalline substance that emits light when a current flows through it. Depending on the crystalline material: red, yellow, green, blue or orange light is produced.

It is not possible to produce white light from any of these materials, so a triad of red, blue and green is placed inside a case and they are all illuminated at the same time to produce white light. Recently, 

LEDs have a cathode and anode lead and must be connected to DC around the correct way. The cathode lead is identified on the body by a flat-spot on the side of the LED. The cathode lead is the shorter lead.

One of the most important things to remember about a LED is the characteristic voltage that appears across it when connected to a voltage. This does not change with brightness and cannot be altered.

For a red LED, this voltage is 1.7v and if you supply it with more than this voltage, it will be damaged. 

The LED will allow the exact voltage to appear across it and the brightness will depend on the value of the resistor. 

Zener diodes (5.2c and 5.2d) are designed to stabilize a voltage. Diodes marked as ZPD5.6V or ZPY15V have operating voltages of 5.6V and 15V. 

Photo diodes (5.2e) are constructed in a way that they allow light to fall on the P-N connection. When there is no light, a photo diode acts as a regular diode. It has high resistance in one direction, and low resistance in opposite direction. When there is light, both resistances are low. Photo diodes and LEDs are the main items in an optocoupler (to be discussed in more detail in chapter 9).

Tunnel diodes (5.2f and 5.2g) are commonly used in oscillators for very high frequencies. 

Schottky diodes (5.2h) are used in high frequency circuits and for its low voltage drop in the forward direction. 

Breakdown diodes (5.2i) are actually Zener diodes. They are used in various devices for protection and voltage regulation. It passes current only when voltage rises above a pre-defined value. 

A Varicap diode (5.2j) is used instead of a variable capacitor in high frequency circuits. When the voltage across it is changed, the capacitance between cathode and anode is changed. This diode is commonly used in radio receivers, transceivers and oscillators.

The cathode of a low power diode is marked with a ring painted on the case, but it is worth noting that some manufacturers label the anode this way, so it is best to test it with a multimeter.

Power diodes are marked with a symbol engraved on the housing. If a diode is housed in a metal package, the case is generally the cathode and anode is the lead coming from the housing.

5.1 Diode identification

European diodes are marked using two or three letters and a number. The first letter is used to identify the material used in manufacturing the component (A - germanium, B - silicon), or, in case of letter Z, a Zener diode. 

The second and third letters specify the type and usage of the diode. Some of the varities are:

A - low power diode, like the AA111, AA113, AA121, etc. - they are used in the detector of a radio receiver; BA124, BA125 : varicap diodes used instead of variable capacitors in receiving devices, oscillators, etc., BAY80, BAY93, etc. - switching diodes used in devices using logic circuits. BA157, BA158, etc. - these are switching diodes with short recovery time.

B - two capacitive (varicap) diodes in the same housing, like BB104, BB105, etc.

Y - regulation diodes, like BY240, BY243, BY244, etc. - these regulation diodes come in a plastic packaging and operate on a maximum current of 0.8A. If there is another Y, the diode is intended for higher current. For example, BYY44 is a diode whose absolute maximum current rating is 1A. When Y is the second letter in a Zener diode mark (ZY10, ZY30, etc.) it means it is intended for higher current.

G, G, PD - different tolerance marks for Zener diodes. Some of these are ZF12 (5% tolerance), ZG18 (10% tolerance), ZPD9.1 (5% tolerance).

The third letter is used to specify a property (high current, for example).

American markings begin with 1N followed by a number, 1N4001, for example (regulating diode), 1N4449 (switching diode), etc.

Japanese style is similar to American, the main difference is that instead of N there is S, 1S241 being one of them.

5.2 Diode characteristics

The most important characteristics when using power diodes is the maximum current in the forward direction (IFmax), and maximum voltage in the reverse direction (URmax).

The important characteristics for a Zener diode are Zener voltage (UZ), Zener current (IZ) and maximum dissipation power (PD).

When working with capacitive diodes it is important to know their maximum and minimum capacitance, as well as values of DC voltage during which these capacitances occur.

With LEDs it is important to know the maximum value of current it is capable of passing. The natural characteristic voltage across a LED depends on the colour and starts at 1.7V for red to more than 2.4v for green and blue. 

Current starts at 1mA for a very small glow and goes to about 40mA. High brightness LEDs and "power LEDs" require up to 1 amp and more. You must know the exact current required by the LED you are using as the wrong dropper resistor will allow too much current to flow and the LED will be damaged instantly. 

The value of this resistors will be covered in another chapter. 

Beside universal transistors TUN and TUP (mentioned in Chapter 4.4), there are universal diodes as well. They are marked with DUS (for universal silicon diode) and DUG (for germanium) on circuit diagrams. 

DUS = Diode Universal Silicon DUG = Diode Universal Germanium

5.3 Practical examples

The diagram of a power supply in figure (3.8) uses several diodes. The first four are in a single package, identified by B40C1500. This is a bridge rectifier.

The LED in the circuit indicates the transformer is working. Resistor R1 is used to limit the current through the LED and the brightness of the LED indicates the approximate voltage.

Diodes marked 1N4002 protect the integrated circuit.

Figure below shows some other examples of diodes. The life of a globe can be increased by adding a diode as shown in 5.3a. By simply connecting it in series, the current passing through the globe is halved and it lasts a lot longer. However the brightness is reduced and the light becomes yellow. The Diode should have a reverse voltage of over 400V, and a current higher than the globe. A 1N4004 or BY244 is suitable.

Unstabilized voltage is marked "U", and stabilized with "UST." Voltage on the Zener diode is equal to UST, so if we want to achieve a stabilized 9V, we would use a ZPD9.1 diode. Although this stabilizer has limited use it is the basis of all designs found in power supplies.

We can also devise a voltage overload detector as sown in figure 5.3d. A LED indicates when a voltage is over a predefined value. When the voltage is lower than the operating voltage of the Zener, the zener acts as a high value resistor, so DC voltage on the base of the transistor is very low, and the transistor does not "turn on." When the voltage rises to equal the Zener voltage, its resistance is lowered, and transistor receives current on its base and it turns on to illuminate the LED. This example uses a 6V Zener diode, which means that the LED is illuminated when the voltage reaches that value. For other voltage values, different Zener diodes should be used. Brightness and the exact moment of illuminating the LED can be set with the value of Rx.

To modify this circuit so that it signals when a voltage drops below some predefined level, the Zener diode and Rx are swapped. For example, by using a 12V Zener diode, we can make a car battery level indicator. So, when the voltage drops below 12V, the battery is ready for recharge.
 a noise-producing circuit, which produces a rain-like sound. DC current flowing through diode AA121 isn't absolutely constant and this creates the noise which is amplified by the transistor (any NPN transistor) and passed to a filter (resistor-capacitor circuit with values 33nF and 100k).